ubee DDW36C

hr23-700 · Post by **hr23-700** » Mon Nov 14, 2016 10:52 pm

how can i add support for Ubee winbond 25q128fvfg
https://www.pjrc.com/teensy/W25Q128FV.pdf
thank you

ricktendo · Post by **ricktendo** » Mon Nov 14, 2016 10:54 pm

You may need to add a new spi flash profile to spiflash.xml

hr23-700 · Post by **hr23-700** » Tue Nov 15, 2016 12:16 am

i was able to read it with scrip6120
but after verifying i get a fail

Post by **usbbdm** » Tue Nov 15, 2016 9:08 am

hr23-700 wrote:i was able to read it with scrip6120
but after verifying i get a fail

This means the connection is not right yet. (ISP is not working for you).

hr23-700 · Post by **hr23-700** » Tue Nov 15, 2016 3:33 pm

can u check please

Post by **usbbdm** » Tue Nov 15, 2016 6:14 pm

hr23-700 wrote:can u check please

How long is your wire to the target? You should keep them as short as possible or use slower clock (6M or 3M).
You have the most setup right.

hr23-700 · Post by **hr23-700** » Fri Nov 18, 2016 10:12 am

sorry for the late response !!!!!!
yes im using 3 foot of usb cable
and from jtag im using the cables u send me
thank you

CAPONE · Post by **CAPONE** » Tue Nov 22, 2016 5:40 pm

hr23-700, That BackUp is No good.

hr23-700 · Post by **hr23-700** » Wed Nov 23, 2016 6:19 pm

thank you guys , so what am i doing wrong
1st i cant read the chip installed in the board
2nd when i could read it its off the board and its reads the wrong stuff
what do i need to read the correct info ?
why i cant read it off the board?
ive been following the lines from chip and the board and it turns out that when i follow pin 1 from spi which its hold there's a surface mount resistor or something like that connects pin 9 which its w with pin1
no idea.....
also im reading it with the sb6120 script,,,
its there's a XML or script for this modems
any help will b appreciate

hr23-700 · Post by **hr23-700** » Wed May 10, 2017 9:59 pm

hey guys i have this modems that i could read but i dont have the right xml
how can i get the proper xml to read and write
the first dump belongs to a UBEE [ATTACH]1125[/ATTACH]DDW365

hr23-700 · Post by **hr23-700** » Wed May 10, 2017 10:01 pm

and this one belongs to DDW36c[ATTACH]1126[/ATTACH]
please any buddy that's know how to create a XML
thank you

CAPONE · Post by **CAPONE** » Thu May 11, 2017 1:40 am

hr23-700 wrote:and this one belongs to DDW36c[ATTACH]1126[/ATTACH]
please any buddy that's know how to create a XML
thank you

SB6120 is 8Mb Flash and these are both 16Mb Flash. You should try instead to read as a DCP3000 which is also a 16Mb Flash. Or you can go in config settings, under Category, chose "Develop", Under Protocol "SPIFLASH" and Under Target, "25128", that will also read the full 16Mb and from that if the compare is Good, a proper XML can be created for that Target.

If you need help, I may be able thru Teamviewer to help you and can show you how to create XML also.

hr23-700 · Post by **hr23-700** » Sat May 13, 2017 11:54 am

they are the same[ATTACH]1129[/ATTACH]

USB JTAG

ubee DDW36C

ubee DDW36C

after desoldering the spi

Who is online