SB5102Mod.xml

[usbbdm]

Use this mod if you want to program single image firmware like haxorware.

[lula]

This is the new programing for 5101u?

ldram image1
program image1
program image0
cmpram image1
cmpram image0

[themob]

Hi don't mean hijack it.. will this work on ambits 256 with usbjag NT?

[Koevoet]

Yes it will , this xml was designed so that you just have to load the haxorware image and program it once ,

commands would be

ldram Image
program image

There is no more need to do image 0 and image 1 with this xml.

Regards

[lula]

Koevoet, I dont need use this commands to program sb5101u;
-flshdct 0
Found Address= 00000000 MX25FL0165A
-getram 0 200000
-save 0 200000
-flshdct 0
Found Address= 00000000 MX25FL0165A
-ldram Image0
-save f image0 ff
-f image1 ff
-f image0 ff
-ldram Image0
-erase 00020000 000e0000
Erase starts...
Erase time 00:00:04 (.187)
-sprogram 20000 e0000
Program Starts...
Script finished
Program speed 265.71 KB/s
Program time 00:00:03 (.656)
Program pass, if no further programming needed, power off/on the target
-erase 00100000 000f0000
Erase starts...
Erase time 00:00:05 (.703)
-sprogram 100000 f0000
Program Starts...
Script finished
Program speed 953.48 KB/s
Program time 00:00:01 (.734)
Program pass, if no further programming needed, power off/on the target
-cmpram Image1
Compare data OK
-cmpram Image0
Compare data OK

Only use
ldram Image
program image
cmpram Image1
cmpram Image0
????????????????????????????

[Koevoet]

@ lula

I am assuming you wish to put the latest haxorware onto your 5101U ??

If so then just load the above xml into your config so that it shows as 5102mod,

Then just use the tabs to write the haxorware image. As you allready have a compatable bootloader on your modem , all you need is to load the firmware image itself.

So ,once you have a backup of your 5101u original image do the following :

1. Detect the modem on the 5102mod config.
2. Click on the Image tab ( Image should now be showing in the drop down box on the left
3. Load Hax rev38 via the folder button on the top left.
4. Click on the write (W) button .
5. This will auto execute the erase and program of the image .
6. Once that is complete click the V button to verify the image , if all is ok , reboot modem and check to see if hax has loaded via 192 gui.

Regards

[lula]

Koevoet and BDM Thanks

[themob]

koevoet,

i am trying to understand to using ambits by usbjtag nt. Are you saying to use usnjtag nt with ambits?? i have try both side and and it don't give me detect it.

it give me this.
right http://www.usbjtag.com 2008,2009,2010
USB JTAG NT 0.32
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 00ff,00ff
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 00ff,00ff
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 00ff,00ff
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 00ff,00ff
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000

I am using usbjtagnt program. what am i missing ? i am sorry if it simple question or me being pea brain. it jus twhole different from sb5101 to ambits.

[Koevoet]

@ themob

does your A256 look like this http://www.usbjtag.com/jtagnt/modem/ambit256.php

if so do you have the ISP connected , the red wire ??
If you followed the pin layout and ISP you will get a detection.

Regards

[lula]

I bricked my sb5101u, old lite put green

[Koevoet]

@ lula could you post a step by step of what you did and how you loaded the firmware ,, the modem wont be bricked , it is still recoverable.

Regards

[themob]

it almost same so you saying that i need to put red wire and then hook up with usbjtag nt so it will detection? if so when it done flash do i need to be remove red wire?

@ themob

does your A256 look like this http://www.usbjtag.com/jtagnt/modem/ambit256.php

if so do you have the ISP connected , the red wire ??
If you followed the pin layout and ISP you will get a detection.

[Koevoet]

Correct , the red wire is in place so that you can do ISP , once the modem is flashed , remove the red wire and boot up the modem as per normal.

Regards

[themob]

after put 2 wire on it. still not detect... so is there suppose to make like adapter ambits for usb jtag nt? just like webstar adapter. One of the guy make adapter with usb jag nt for website??

Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 00ff,00ff
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 00ff,00ff
-flshdct 0
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0

[lula]

first step detect, in the range mark image then loook the foulder and upload the haxor and programing (W). When I verificate cmpram image (V) not said ok. Christmas, old lite green