New software porting thread.

News to announce.
Locked
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

New software porting thread.

Post by usbbdm »

I am making this thread dedicated to the project of porting NT software to new platform so it is possible to run NT software on Linux and mac.

The porting is smooth. I am now porting the hex editor porting. This is most time consuming part. I will expect this to take 3-5 days. Hex editor is very useful for experienced user and you can watch data live flow between software and target.
After that I will start to add the USB part to it and we will see true data read/write to the target.
Here is the screen capture of the new look of the NT software.
Image

You now can select target without quit application or unplug USB (If the hardware is the same, if you switch between BDM and USB you need to unplug USB of course).

0.41 will be feature and look feel compatible to 0.40. In the future we might add significant features that based on the feedback from the forum.
ftaram
Junior Member
Posts: 18
Joined: Thu Nov 26, 2009 11:09 am

Post by ftaram »

Great news I use Mac as primary operating system tank you usbbdm
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

I like the New look of the software.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

USBBDM
Will it be posible to see changes made to Plat for example.
If one reads the plat then modify the UID , Will the program hex sbe able to show location where changes where made?
Like in Ultra Compare for example. If you open original plat and mod plat it will compare both and highlight in red where thers a diffrence in hex data.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

TUNDRA wrote:USBBDM
Will it be posible to see changes made to Plat for example.
If one reads the plat then modify the UID , Will the program hex sbe able to show location where changes where made?
Like in Ultra Compare for example. If you open original plat and mod plat it will compare both and highlight in red where thers a diffrence in hex data.
This is an idea and can be considered in the future.
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

Finally I have finished the hex display and editing.
I have also added "copy" and "paste" (This does not work on current NT software).
Another BIG feature is the drag-drop, now you can drag a file to the memory tab so you do not need to open file every time. This is consider huge improvement to the UI code.
I will now start to port the CLI (command line interface) code. This should not be too difficult.
konnan
Junior Member
Posts: 221
Joined: Tue Apr 03, 2007 7:04 pm

Post by konnan »

Master USBBDM. I use a mac book it would be terrific, thanks again.
ufo
Junior Member
Posts: 117
Joined: Thu Aug 14, 2008 2:07 pm

Post by ufo »

Than you, thank you thank you!!!!!!!!!!
Highlighting changes as already requested would be a GREAT added feature.

Still you are amazing and appreciated.
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

The CLI input had 90% done. Now need to add each command to the command list. Then the JTAG target (MIPS,ST20,BDM,SPI,EEPROM,MIPS64 etc).
konnan
Junior Member
Posts: 221
Joined: Tue Apr 03, 2007 7:04 pm

Post by konnan »

master Usbbdm: will you release a version for mac?
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

konnan wrote:master Usbbdm: will you release a version for mac?
I hope so. The porting is smooth but takes time to do it.
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

Finished commands are

Code: Select all

help
cls
ldram
config
configshow
f
exit
I will start to add the USB code tonight.
konnan
Junior Member
Posts: 221
Joined: Tue Apr 03, 2007 7:04 pm

Post by konnan »

Beautiful.....thanks
javicali
Junior Member
Posts: 16
Joined: Sun Jul 25, 2010 1:40 pm

Post by javicali »

USBBDM hello any new for XC in this future version!!??is beatiful :D:D:D
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

USB framework is done. BDM is about 40% complete.BDM should be finished in one or two days. Then will port script first and then EJTAG.
Locked

Who is online

Users browsing this forum: No registered users and 8 guests