Dct2224 no lights
-
- Junior Member
- Posts: 53
- Joined: Sat Sep 25, 2010 2:22 pm
Dct2224 no lights
Good day to everyone i programed my dct2224 and now no lights what do i need to do or can someone teamviewer me and i have a 2524 that the display is ddr.
thank you
thank you
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
Need to write Back a Good BackUp. Which I hope you Did A BackUp Before Testing.unnatl wrote:Good day to everyone i programed my dct2224 and now no lights what do i need to do or can someone teamviewer me and i have a 2524 that the display is ddr.
thank you
For the DCT2500 Write back a Good Boot & Plat.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
For DCT2524 use this command to see if you need to use "erase" or "sprogram"
If you do not see TRAP ON, then you need to power off/on the box and use "erase" and "sprogram" the boot. Erase the plat also. Then power off/on again to use "program" command.
If you see TRAP ON then it is OK to use "program".detect
program
If you do not see TRAP ON, then you need to power off/on the box and use "erase" and "sprogram" the boot. Erase the plat also. Then power off/on again to use "program" command.
-
- Junior Member
- Posts: 53
- Joined: Sat Sep 25, 2010 2:22 pm
okay here is what i did on the 2224 still no lights.
reset 1
-R
-init
-flshdct code
Found Address= 00400000 Intel 28F160C3B
-ldram code
I:/DCT-2224-0775/Code-0527.bin loaded
-ldram nvram
I:/DCT-2224-0775/NVRAM-0775.bin loaded
-setram nvram
-r a7 200400
-r rpc 468
-program code
Erase starts...
Erase time 00:00:23 (.572)
Program Starts...
Program speed 158.54 KB/s
Program time 00:00:13 (.228)
Program pass, if no further programming needed, power off/on the target
-cmpram code
Time 00:00:05 (.336)
Compare data OK
-reset
-R
reset 1
-R
-init
-flshdct code
Found Address= 00400000 Intel 28F160C3B
-ldram code
I:/DCT-2224-0775/Code-0527.bin loaded
-ldram nvram
I:/DCT-2224-0775/NVRAM-0775.bin loaded
-setram nvram
-r a7 200400
-r rpc 468
-program code
Erase starts...
Erase time 00:00:23 (.572)
Program Starts...
Program speed 158.54 KB/s
Program time 00:00:13 (.228)
Program pass, if no further programming needed, power off/on the target
-cmpram code
Time 00:00:05 (.336)
Compare data OK
-reset
-R
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
Like I said. Sounds like you have a Bad BackUp. If the Code BackUp where good you Should get Light. Then Program the Nvram.unnatl wrote:okay here is what i did on the 2224 still no lights.
reset 1
-R
-init
-flshdct code
Found Address= 00400000 Intel 28F160C3B
-ldram code
I:/DCT-2224-0775/Code-0527.bin loaded
-ldram nvram
I:/DCT-2224-0775/NVRAM-0775.bin loaded
-setram nvram
-r a7 200400
-r rpc 468
-program code
Erase starts...
Erase time 00:00:23 (.572)
Program Starts...
Program speed 158.54 KB/s
Program time 00:00:13 (.228)
Program pass, if no further programming needed, power off/on the target
-cmpram code
Time 00:00:05 (.336)
Compare data OK
-reset
-R
Try Finding a Goos Code BackUp to write to your Box to see if you get it to turn On Properly.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
As Long as they have a decent amount of channells, Then you can do the Hardware MOD to them To Block the Return Signal.unnatl wrote:Thank tundra got the 2524 back online and the 2224 I have a lot of rng 110 what can i do with them pm and let me know thanks for all of your help.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
Who is online
Users browsing this forum: No registered users and 5 guests