I suggest you use NT. It can adjust the BDM clock. 6M/3M/1.5M. I found some MC68332 does not like 6M clock (Old BDM had one BDM clock only).[email protected] wrote:Yes usbbdm, it is a Motorola 68332 out of a 1997 Monte Carlo. I have installed and wired a BDM header and jumped the lands on the board which enable BDM. The instructions for this were from flash dump on diy efi (Steve Ravet).
Thanks
Mark
USB BDM NT user please read.
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
-
- Junior Member
- Posts: 4
- Joined: Tue Jun 08, 2010 5:44 pm
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
You need[email protected] wrote:I have tried to connect to the car PCM but the software says "incompatible Device". I don't think that I'm in BDM mode as I see JTAG connection diagrams in the left panel. I sure could use some help.
Thanks,
Mark
1. BDM NT (Old BDM does not have adjustable clock).
2. Select the ECU target.
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
enter the e-mail used when you bought the Tool then click on Activate Online. It will get it for you. No need to remember it after initioal activation.cesar wrote:what should i do if i lost the activation code
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
It will not work if this is the first time activating Tool. You must send e-mail with S/N Number to get activation Code. After this you can simply Use the Activate on line by entering just the e-maill addy use for purchase of tool.madwolf wrote:Tried to activate online, getting error=hardware not exist.
Hardware is properly installed and the ID is displayed in the activation box.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
-
- Junior Member
- Posts: 1
- Joined: Mon Apr 30, 2012 5:02 pm
dcttesting - not activated
greetings.
I need help because my usbbdm software tells me in the top-dcttesting not activated. preciento this and not let me do all the functions to the 2224. I also give getram nvram and pretends to read it but when I verify everything is at zero. software is the 0.57
thanks in advance ...
I need help because my usbbdm software tells me in the top-dcttesting not activated. preciento this and not let me do all the functions to the 2224. I also give getram nvram and pretends to read it but when I verify everything is at zero. software is the 0.57
thanks in advance ...
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
I think the software is not activated. Did you get activation code?zapirocco wrote:greetings.
I need help because my usbbdm software tells me in the top-dcttesting not activated. preciento this and not let me do all the functions to the 2224. I also give getram nvram and pretends to read it but when I verify everything is at zero. software is the 0.57
thanks in advance ...
To get activation code send email to [email protected]
For tech support send [email protected] ( A screen capture should do some help).
-
- Junior Member
- Posts: 22
- Joined: Wed Feb 12, 2020 2:46 am
- Location: Northwest US
- Contact:
U-LINK will not activate USB-JTAG software
Hi.
I just received my new U-LINK NT interface (v1.45)
Installed drivers and USB-JTAG NT (U-LINK NT) setup.
Inserted the U-LINK to USB and ran the software
The GUI came up with the default DCT2224 selected.
Selected tools > activation
Entered email as directed and pressed online activation.
Instead of activation code, I get "error=please try again later"
The status bar shows USB connected/BDM off
Title bar shows testing DCT2224 not activated.
What can be done to get this activated ?
TYIA
boxnut
I just received my new U-LINK NT interface (v1.45)
Installed drivers and USB-JTAG NT (U-LINK NT) setup.
Inserted the U-LINK to USB and ran the software
The GUI came up with the default DCT2224 selected.
Selected tools > activation
Entered email as directed and pressed online activation.
Instead of activation code, I get "error=please try again later"
The status bar shows USB connected/BDM off
Title bar shows testing DCT2224 not activated.
What can be done to get this activated ?
TYIA
boxnut
Some of my information may be incorrect, incomplete,or just plain wrong. Seems I am human.
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
Re: USB BDM NT user please read.
Check your email now and you should get the code.
In the mean time if you need help please go www.usbjtag.com (not the forum). Any page will popup a dialog to chat with me.
In the mean time if you need help please go www.usbjtag.com (not the forum). Any page will popup a dialog to chat with me.
Who is online
Users browsing this forum: No registered users and 5 guests