Forceware programming on 6141/USBJTAG-NT
Moderators: justsomeguy, Koevoet
-
- Junior Member
- Posts: 3
- Joined: Sat Aug 15, 2015 7:55 pm
Forceware programming on 6141/USBJTAG-NT
I have the USBJTAG-NT using software 0.76
For some reason I can't get forceware to come up after flashed.
I can detect the flash with no issues. Here are the steps I am using
Detect flash
Select UBFI1 tab , under file I select forceWare-1.4b1-mod2.bin
WRITE
Select UBFI2 tab , under file I select forceWare-1.4b1-mod2.bin
WRITE
After that is complete I unplug USBJTAG-NT , 5volt USB and power.
Plug 12vDC power back in , it's stuck with a solid top green light. Won't try and go though a boot process.
My 2nd attempt was to load Forceware on bank 1 by itself ,all good then and modem will boot but I can't get the the forceware page.
3rd attempt was to drag and drop the firmware into USBJTAG-NT and program each bank , but same result .
It seems as soon as forceWare-1.4b1-mod2.bin is loaded on UBFI2 the modem becomes non bootable.
I've been at this for days and hours . If anyone could point me in the right direction it would be great !
Thanks
For some reason I can't get forceware to come up after flashed.
I can detect the flash with no issues. Here are the steps I am using
Detect flash
Select UBFI1 tab , under file I select forceWare-1.4b1-mod2.bin
WRITE
Select UBFI2 tab , under file I select forceWare-1.4b1-mod2.bin
WRITE
After that is complete I unplug USBJTAG-NT , 5volt USB and power.
Plug 12vDC power back in , it's stuck with a solid top green light. Won't try and go though a boot process.
My 2nd attempt was to load Forceware on bank 1 by itself ,all good then and modem will boot but I can't get the the forceware page.
3rd attempt was to drag and drop the firmware into USBJTAG-NT and program each bank , but same result .
It seems as soon as forceWare-1.4b1-mod2.bin is loaded on UBFI2 the modem becomes non bootable.
I've been at this for days and hours . If anyone could point me in the right direction it would be great !
Thanks
-
- Junior Member
- Posts: 13
- Joined: Sat Sep 19, 2009 8:56 am
You need to log in to the modem and start it. Forceware came with auto start off, so you need to start it yourself. goto 192.168.100.1debug337 wrote:I have the USBJTAG-NT using software 0.76
For some reason I can't get forceware to come up after flashed.
I can detect the flash with no issues. Here are the steps I am using
Detect flash
Select UBFI1 tab , under file I select forceWare-1.4b1-mod2.bin
WRITE
Select UBFI2 tab , under file I select forceWare-1.4b1-mod2.bin
WRITE
After that is complete I unplug USBJTAG-NT , 5volt USB and power.
Plug 12vDC power back in , it's stuck with a solid top green light. Won't try and go though a boot process.
My 2nd attempt was to load Forceware on bank 1 by itself ,all good then and modem will boot but I can't get the the forceware page.
3rd attempt was to drag and drop the firmware into USBJTAG-NT and program each bank , but same result .
It seems as soon as forceWare-1.4b1-mod2.bin is loaded on UBFI2 the modem becomes non bootable.
I've been at this for days and hours . If anyone could point me in the right direction it would be great !
Thanks
-
- Junior Member
- Posts: 4
- Joined: Tue Feb 16, 2010 9:55 pm
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
Who is online
Users browsing this forum: No registered users and 5 guests