Is this gonna be supported

Use USB JTAG NT on VOIP device so we can unlock the device or configure the device.
Post Reply
Whammy45
Junior Member
Posts: 30
Joined: Sun May 22, 2011 4:50 am

Post by Whammy45 »

Thanks Capone I know that it will eventually get supported when usbdm gets back from his vacation.
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

Whammy45 wrote:Thanks Capone I know that it will eventually get supported when usbdm gets back from his vacation.
LOL What Little Faith you Have. It has already Been Dumped. And No help from USBBDM.

U-Boot 1.2.0 (Feb 24 2011 - 15:47:07)
PSPU-Boot 1.2.1.48

DRAM: 64 MB
Macronix MX25l12805D flash found
Flash: 16 MB

In: serial
Out: serial
Err: serial
Running RAM test
RAM test passed
*** ACTIMAGE = 1, will try to boot UBFI1 stored @0x48040000
## Executing script at 48040000

The Above Inforamtion Alone Is More than Enough to Firgure Out How to Make it Work in the USBJTAG NT Software.
thebuzzer
Junior Member
Posts: 2
Joined: Mon Jul 16, 2012 2:57 pm

Post by thebuzzer »

anyone got the 802g to use spi clip method?
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

thebuzzer wrote:anyone got the 802g to use spi clip method?

I read it is like the 6120 modem pinout but I followed the 6120 diagram i found and cant read the flash chip still. I am not too sure what I am doing wrong. Anyone can lead me to the right direction?

Clips are very Unreliable. Soldering to the SPI Flash Is better, If your good at soldering that is. As far as the Pin out, if its a 16 Pin SPI Flash will be the same as SB6120 and 8 Pin SPI just like SB5101U. And Please Keep post in one Section. No need to Post twice to get responce.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
thebuzzer
Junior Member
Posts: 2
Joined: Mon Jul 16, 2012 2:57 pm

Post by thebuzzer »

ya i suck in soldering

so i am trying to use the clip method

it seems like

http://www.dz863.com/pinout-819072063-MX25L12805D/

if same as the diagram to wire the 6120

Image


pin 2 is powering the board when i turn on the 3.3v i see the lights go on. however I am just getting FF,FF,FF for all my readings. not too sure why
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

thebuzzer wrote:ya i suck in soldering

so i am trying to use the clip method

it seems like

http://www.dz863.com/pinout-819072063-MX25L12805D/

if same as the diagram to wire the 6120

pin 2 is powering the board when i turn on the 3.3v i see the lights go on. however I am just getting FF,FF,FF for all my readings. not too sure why
Like I told you Before, the Wireing is the Same on all SPI Flash No mater the Model of Modem, SB6120, UBEE, DPC3000,,,,,,,

And yes its normal to see some Lights on Board. You can try 5 volts instead of 3.3. Never go Over 5 Volts.
I am sure its User Error related. When providing external power you need 2 wires. One for Postive Voltage and One for Ground, Regardles of Ground Wire from USBJTAG NT, WIre 2...............
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
Whammy45
Junior Member
Posts: 30
Joined: Sun May 22, 2011 4:50 am

Anyone figure out how to do this yet

Post by Whammy45 »

Copyright (C) 2010,2011,2012
USB JTAG NT 0.57
Target: TM802G
-speed 2
-flshdct 0
Found Address= 00000000 W25Q128CV
-erase 0 1000000
Erase starts...
Erase time 00:00:00 (.082)
-erase 0 1000000
Erase starts...
Erase time 00:00:00 (.083)


This the reading i get from an 802 with the wb chip it read & verifies but isn't erasing properly maybe am missing something with this one I've tested both the mx & sp chip's but the wb problems...
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

How did you connected it? When chip is detected, if you cannot erase the chip, it should related the pins that control the write (hold, write enable) are having wrong level.
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

Whammy45 wrote:Copyright (C) 2010,2011,2012
USB JTAG NT 0.57
Target: TM802G
-speed 2
-flshdct 0
Found Address= 00000000 W25Q128CV
-erase 0 1000000
Erase starts...
Erase time 00:00:00 (.082)
-erase 0 1000000
Erase starts...
Erase time 00:00:00 (.083)


This the reading i get from an 802 with the wb chip it read & verifies but isn't erasing properly maybe am missing something with this one I've tested both the mx & sp chip's but the wb problems...
I am able to read and write to the TM802G with no problem. Like USBBDM said, It may be user error on the wiring.....
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
Whammy45
Junior Member
Posts: 30
Joined: Sun May 22, 2011 4:50 am

Post by Whammy45 »

Ok guys I did a 802g that had the chip MX on it no problem it read, verify and erase, also the same thing with the chip that say SP on it, but for some reason the one with the wb I can only read and verify, but its not erasing I tried both 3.3 & 5 volts to pin 2 of the chip but nothing am using a external power from the usb on my cpu which i tested...
Whammy45
Junior Member
Posts: 30
Joined: Sun May 22, 2011 4:50 am

Post by Whammy45 »

Ok so no reply means what an error on my end no cause I got a buddy who is doing some testing also that have the same problem relating to the 802g with the winbond chipset....
Moving on usbdm will their be support add for the arris 822g....
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

Whammy45 wrote:Ok so no reply means what an error on my end no cause I got a buddy who is doing some testing also that have the same problem relating to the 802g with the winbond chipset....
Moving on usbdm will their be support add for the arris 822g....
If its anything like the 722G then it can be easily supported. Not sure if by default the software does the 722G, However I have been able to read and program the 722G. I don't remember if I made the DLL for it or not, I do have it listed in my Targets.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

CAPONE wrote:If its anything like the 722G then it can be easily supported. Not sure if by default the software does the 722G, However I have been able to read and program the 722G. I don't remember if I made the DLL for it or not, I do have it listed in my Targets.
I do not think you can make dll for it as I did not publish how to make dll yet.
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

usbbdm wrote:I do not think you can make dll for it as I did not publish how to make dll yet.
Yes, I ment to say XML for that Target. Not that you WOULD EVER Publish how to make DLL. LOL ;)
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
Whammy45
Junior Member
Posts: 30
Joined: Sun May 22, 2011 4:50 am

Post by Whammy45 »

Well if u need one to create support for it let me know am will to donate it pm me and I will send it to u thanks will also send u the 802g with the windbond chip..
Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests