dct2000 cr4
-
- Junior Member
- Posts: 88
- Joined: Fri Apr 11, 2008 5:45 pm
dct2000 cr4
on the board says excatly
GI DCT2000 CR4 MB
240-584-615-99-RD
can somebody tell me please how to fuid ?
what commands i should use . i only did ph 7,8,9 till now and i dont want to messup this one..
please can somebody write the correct command to fuid.
thnx
GI DCT2000 CR4 MB
240-584-615-99-RD
can somebody tell me please how to fuid ?
what commands i should use . i only did ph 7,8,9 till now and i dont want to messup this one..
please can somebody write the correct command to fuid.
thnx
-
- Junior Member
- Posts: 278
- Joined: Sun Apr 26, 2009 3:43 pm
connect the usbbdm then connect power
run usbjtagnt software and change the config to dct2224 then use these commands
reset 1
init
getram nvram
getram code
save nvram
save code
firm (make your changes in the popup)
flshdct code
program code
If you need to connect the box or change the upm then also do this:
connect
upm (enter new upm)
setram nvram
reset (when done)
run usbjtagnt software and change the config to dct2224 then use these commands
reset 1
init
getram nvram
getram code
save nvram
save code
firm (make your changes in the popup)
flshdct code
program code
If you need to connect the box or change the upm then also do this:
connect
upm (enter new upm)
setram nvram
reset (when done)
-
- Junior Member
- Posts: 88
- Joined: Fri Apr 11, 2008 5:45 pm
unit is 2244
unit is 2244 does it any difference. and i never change upm . could you explain me what upm does? thanx for reply
-
- Junior Member
- Posts: 88
- Joined: Fri Apr 11, 2008 5:45 pm
something is wrong with cr4
reset 1
init
getram nvram
getram code
save nvram
save code
after this step i go to dct testing menu and firmware test but it doesnt pull up anything says
Firmware Test
Firmware not supported
then tried to flash code
-flshdct code
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum ffff,ffff
and the box is dct2000 cr4 i use bdm nt cable and box has premium channels
what step is wrong to fake uid???
init
getram nvram
getram code
save nvram
save code
after this step i go to dct testing menu and firmware test but it doesnt pull up anything says
Firmware Test
Firmware not supported
then tried to flash code
-flshdct code
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum ffff,ffff
and the box is dct2000 cr4 i use bdm nt cable and box has premium channels
what step is wrong to fake uid???
-
- Junior Member
- Posts: 88
- Joined: Fri Apr 11, 2008 5:45 pm
one step ahead but still can not program it after fuid
-reset 1
-R
-init
-getram nvram
-getram code
-firm
Do not forget to program the chip
-flshdct code
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum ffff,ffff
-program code
Use DETECT to detect the flash type
after i did fuid then wont let me program it back i think something on commands is wrong ??? i think shoul be program xxxxx to xxxxx??? instead just flash code and program code?????????????
please help
-R
-init
-getram nvram
-getram code
-firm
Do not forget to program the chip
-flshdct code
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum ffff,ffff
-program code
Use DETECT to detect the flash type
after i did fuid then wont let me program it back i think something on commands is wrong ??? i think shoul be program xxxxx to xxxxx??? instead just flash code and program code?????????????
please help
-
- Junior Member
- Posts: 278
- Joined: Sun Apr 26, 2009 3:43 pm
Who is online
Users browsing this forum: No registered users and 3 guests