DCI105COM1 change unit id???

jackmode · Post by **jackmode** » Sat Oct 06, 2012 2:32 pm

does any body knows how to change the unit id or no were its located in the flash i found were the channels are but cant seem to find the unit id

jackmode · Post by **jackmode** » Tue Oct 09, 2012 8:08 am

or a way to fake it something??

Post by **usbbdm** » Tue Oct 09, 2012 10:06 am

jackmode wrote:or a way to fake it something??

No. The way to fake ID is to analyze the firmware and do proper patch. So far nobody had done any work on it as far as I know.

jackmode · Post by **jackmode** » Tue Oct 09, 2012 12:12 pm

thats a shame this box has a lot of potential i can see the cannel lineup in data 1 and data2 i believe is the nvram i guess I'm going to continue testing

Post by **usbbdm** » Tue Oct 09, 2012 1:18 pm

Other than connect with JTAG NT and programming it I have done nothing to it. I did not even connect it to TV. I think if we spend some time on it we could get something done.

jackmode · Post by **jackmode** » Tue Oct 09, 2012 3:29 pm

well im testing but i suck at coding and binaries but it would be nice if i could modyfi the channel map to get more channels does anybody no were to start? that would be the main thing i would be intrested in since i found were its located

willowtree001 · Post by **willowtree001** » Wed Oct 24, 2012 10:53 pm

This small box does program with the NT equipment very nicely. The flash is only 2MB or less if i remember. Somone should be able to disassemble flash and find out with ease.

Post by **usbbdm** » Thu Oct 25, 2012 9:48 pm

willowtree001 wrote:This small box does program with the NT equipment very nicely. The flash is only 2MB or less if i remember. Somone should be able to disassemble flash and find out with ease.

The first thing to do is to unpack the firmware. Then disassemble it and patch and put back. I will see if I can take a look of this firmware.

willowtree001 · Post by **willowtree001** » Thu Oct 25, 2012 11:25 pm

noticed this when attempting to unpack
inflate 1.2.3.
mark adler

willing to send you image i pulled out a box usbbdm just write me PM
Mines works for a week then goes down...if i reprogram will work again ...

Post by **usbbdm** » Fri Oct 26, 2012 8:09 am

willowtree001 wrote:noticed this when attempting to unpack
inflate 1.2.3.
mark adler

willing to send you image i pulled out a box usbbdm just write me PM
Mines works for a week then goes down...if i reprogram will work again ...

What kind of the remote it uses? Can it use regular remote from DCT700?
How do you see "inflate...". Do you hook up the serial port?

Post by **usbbdm** » Fri Oct 26, 2012 8:03 pm

Can anyone send me a few firmware versions? I would like to play with them and see if I can unpack it first.

willowtree001 · Post by **willowtree001** » Sun Oct 28, 2012 7:48 pm

whats your email I send to you asap

Post by **usbbdm** » Sun Oct 28, 2012 7:51 pm

willowtree001 wrote:whats your email I send to you asap

Run NT software and click "about..."

jackmode · Post by **jackmode** » Sat Nov 03, 2012 2:16 pm

willowtree001 wrote:noticed this when attempting to unpack
inflate 1.2.3.
mark adler

willing to send you image i pulled out a box usbbdm just write me PM
Mines works for a week then goes down...if i reprogram will work again ...

the reason it keeps going down it is because your uid is blacklisted the best way to keep it up is to change it or use a filter to block the uplink and always make shore your firmware is the latest

keja · Post by **keja** » Sat Nov 03, 2012 5:19 pm

I don't know what unit u guys are talking about, but it sounds promissing.

USB JTAG

DCI105COM1 change unit id???

DCI105COM1 change unit id???

Who is online