sb5101u/n

SB5XXX,SBV5XXX
Post Reply
lula
Junior Member
Posts: 86
Joined: Tue Jun 23, 2009 7:10 pm

sb5101u/n

Post by lula »

My cable company have new version in sb5101n/u and I try to put haxorware and do not write the haxorware. please let me know if in the SB5101-2.7.6.0-GA-00-NOSH I write haxorware and in the Sb5101NU-2.1.1.0-GA-01-83-NOSH do not allow write haxorware? sorry for my english. I have full backup of new version. I use this commands;
Copyright http://www.usbjtag.com 2008,2009,2010
USB JTAG NT 0.32
-flshdct 0
Found Address= 00000000 MX25FL0165A
-getram 0 200000
-save 0 200000
-flshdct 0
Found Address= 00000000 MX25FL0165A
-ldram Image0
-save f image0 ff
-f image1 ff
-f image0 ff
-ldram Image0
-erase 00020000 000e0000
Erase starts...
Erase time 00:00:04 (.187)
-sprogram 20000 e0000
Program Starts...
Script finished
Program speed 265.71 KB/s
Program time 00:00:03 (.656)
Program pass, if no further programming needed, power off/on the target
-erase 00100000 000f0000
Erase starts...
Erase time 00:00:05 (.703)
-sprogram 100000 f0000
Program Starts...
Script finished
Program speed 953.48 KB/s
Program time 00:00:01 (.734)
Program pass, if no further programming needed, power off/on the target
-cmpram Image1
Compare data OK
-cmpram Image0
Compare data OK
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

For the SB5101U, Use SB5102Mod as Target and Haxoware will Load just fine on that model.

With UJMODEM, Pick SB5102Mod as Target then in the Range Tab set to Image, Load Haxoware then Write.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
lula
Junior Member
Posts: 86
Joined: Tue Jun 23, 2009 7:10 pm

Post by lula »

in the data sheet I view this; WP#/ACC Write protection: connect to GND ; 9.5~10.5V for program/erase acceleration: connect to 9.5~10.5V.... but this the usbjtagnt dont write haxorware beacuse have protection. The acc in the spi chip is pin 3, I need know if I put 10v in the pin3 of spi the NT work fine ?
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

lula wrote:in the data sheet I view this; WP#/ACC Write protection: connect to GND ; 9.5~10.5V for program/erase acceleration: connect to 9.5~10.5V.... but this the usbjtagnt dont write haxorware beacuse have protection. The acc in the spi chip is pin 3, I need know if I put 10v in the pin3 of spi the NT work fine ?
You are wrong.
If you see
-cmpram Image0
Compare data OK

Then you do not need to do anything hardware. You are fully capable to write to the flash. If it does not load your software, you might have select the wrong firmware or program to the wrong place, etc. Do not focus on modifying the hardware.
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

usbbdm wrote:You are wrong.
If you see
-cmpram Image0
Compare data OK

Then you do not need to do anything hardware. You are fully capable to write to the flash. If it does not load your software, you might have select the wrong firmware or program to the wrong place, etc. Do not focus on modifying the hardware.
He is doing it Wrong, To write Haxoware, He MUST use SB5102MOD as target and write Image, Not Image 0, Image 1, That wont Work....
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests