Re: Debrick not working for DCT2500

virus.b · Post by **virus.b** » Mon Mar 02, 2009 12:36 pm

Seems like the Debrick command still does not work. It still says "Unknown Flash Type"....any ideas??

debrick
detect
IDCODE 2711517F
Broadcom BCM7115
IMPCODE 800908
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
debrick
detect
IDCODE 2711517F
Broadcom BCM7115
IMPCODE 800908
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000

virus.b · Post by **virus.b** » Wed Mar 04, 2009 12:43 pm

Problem fixed using the CE 3.3V method... but now, it still says 8888.... any ideas?

Post by **usbbdm** » Wed Mar 04, 2009 2:35 pm

You need right firmware to program back. That is the key. Try to get the same boot from another box.

lalokera · Post by **lalokera** » Sun Mar 08, 2009 10:57 am

i GOT SAME ISSUE ,Copyright http://www.usbjtag.com 2008,2009,2010
Do not use this software if your product is not copyrighte http://www.usbjtag.com
debrick
detect
IDCODE 2711517F
Broadcom BCM7115
IMPCODE 00800908
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
detect
IDCODE 2711517F
Broadcom BCM7115
IMPCODE 00800908
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
getram 9fc00000 200000

Post by **usbbdm** » Sun Mar 08, 2009 11:09 am

debrick is removeed for USB JTAG NT as it does not really work on some device. NT uses "tap" command and that works better.

keja · Post by **keja** » Mon Oct 25, 2010 12:44 am

I have all 8's on my 2500 when I try to debrick it, after I write the tap command, the tutorial says that the DEBUG should be on, but mine says debug off. I tried the peek method it suggest with no good results. Is there anymore info I could get with this problem.

CAPONE · Post by **CAPONE** » Mon Oct 25, 2010 5:25 am

keja wrote:I have all 8's on my 2500 when I try to debrick it, after I write the tap command, the tutorial says that the DEBUG should be on, but mine says debug off. I tried the peek method it suggest with no good results. Is there anymore info I could get with this problem.

Follow the Tutorial to a T And it Works.

Post by **usbbdm** » Mon Oct 25, 2010 7:42 am

keja wrote:I have all 8's on my 2500 when I try to debrick it, after I write the tap command, the tutorial says that the DEBUG should be on, but mine says debug off. I tried the peek method it suggest with no good results. Is there anymore info I could get with this problem.

Use J200 method. Connect J200, then issue TAP command and see DEBUG ON. Then remove J200.

keja · Post by **keja** » Mon Oct 25, 2010 8:57 am

usbbdm wrote:Use J200 method. Connect J200, then issue TAP command and see DEBUG ON. Then remove J200.

Thanks guys for the help, but what is J200? I'll look around the site to see if I can find some info on J200 method.

CAPONE · Post by **CAPONE** » Mon Oct 25, 2010 9:17 am

keja wrote:Thanks guys for the help, but what is J200? I'll look around the site to see if I can find some info on J200 method.

Locate J200 Will be a 2 pin Header on the DCT2500 Mother Board.

moddog · Post by **moddog** » Mon Oct 25, 2010 9:32 am

Keja get to kno the device it all about testing dude:)

USB JTAG

Re: Debrick not working for DCT2500

Re: Debrick not working for DCT2500

Re: Flash Detected Now!

Who is online