Debrick in dvi3120 possible?

JTAG on DVI3000.

Moderator: elkora

Locked
dagra82
Junior Member
Posts: 108
Joined: Fri Apr 07, 2006 1:27 pm

Debrick in dvi3120 possible?

Post by dagra82 »

yesterday I try to schedule my dvi 3120. The NT usbjtag me well and program correctly detected, I disconnect the dvi3120 and reconnected to the electrical network and check and gave me fault. Now I usbjtag NT detects the flash.

Copyright http://www.usbjtag.com 2008,2009,2010
USB JTAG NT 0.34b
-detect
IDCODE 2711517F
Broadcom BCM7115
IMPCODE 00800908
EJTAG V1, V2.0
DMA supoorted

debrik I can do? and restore flash
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

dagra82 wrote:yesterday I try to schedule my dvi 3120. The NT usbjtag me well and program correctly detected, I disconnect the dvi3120 and reconnected to the electrical network and check and gave me fault. Now I usbjtag NT detects the flash.

Copyright http://www.usbjtag.com 2008,2009,2010
USB JTAG NT 0.34b
-detect
IDCODE 2711517F
Broadcom BCM7115
IMPCODE 00800908
EJTAG V1, V2.0
DMA supoorted

debrik I can do? and restore flash
I have not tested 3120 and I assume it is the same as 3100. It has boot block protection and watchdog. So you need to use xml for 3100. Try to use tap c and tap a ffffffff and see if you can detect flash.
dagra82
Junior Member
Posts: 108
Joined: Fri Apr 07, 2006 1:27 pm

Post by dagra82 »

The dvi 3120 has the same flash that dvi3000. I have removed the watchdog to set the boot and also the watchdog to program the firmware. I use the xml dvi3000 and I have always worked well less yesterday.
usbjtag nt sometimes I can detect the flash and read the boot and firmware, but when I tell him I schedule it crashes .
The dvi3120 has erased the boot and corrupt the firmware.
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

dagra82 wrote:The dvi 3120 has the same flash that dvi3000. I have removed the watchdog to set the boot and also the watchdog to program the firmware. I use the xml dvi3000 and I have always worked well less yesterday.
usbjtag nt sometimes I can detect the flash and read the boot and firmware, but when I tell him I schedule it crashes .
The dvi3120 has erased the boot and corrupt the firmware.
If you are sure watchdog is removed and you can program boot then it will be similar to DCT2500.
use tap c and tap a ffffffff
then you should see DEBUG ON.
Detect see if you get the flash. If not type flshdct 9fc00000 to see if flash shows up.
If flash shows at 9fc00000 then you you should select DMABoot and use "erase" and "sprogram" the boot. Then select back the normal dvi xml.
dagra82
Junior Member
Posts: 108
Joined: Fri Apr 07, 2006 1:27 pm

Post by dagra82 »

Copyright http://www.usbjtag.com 2008,2009,2010
USB JTAG NT 0.35
-detect
IDCODE 2711517F
Broadcom BCM7115
IMPCODE 00800908
EJTAG V1, V2.0
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum ffff,ffff
-tap c
Eco :25110444
-tap a ffffffff
Eco :04C12000
-detect (debug ON )
IDCODE 2711517F
Broadcom BCM7115
IMPCODE 00800908
EJTAG V1, V2.0
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 1800,8900
-flshdct 9fc00000
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum f3f3,f3f3
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

In DCT2500 there is a jumper 200. Do you see similar jumper? This will will help to debrick.
dagra82
Junior Member
Posts: 108
Joined: Fri Apr 07, 2006 1:27 pm

Post by dagra82 »

Lord usbbdm sorry but I could not program the flash I have tried everything and I think the best solution is to change the flash of the other already scheduled. The plate 3120 has dvi smaller and has no internal power supply but external. I think the dvi 3120 are of poor quality
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

If you think this is dead and want to donate for me to test a new device you can donate to me. I might be able to support it in the future software.
I will use 3.3v method at last but will certainly look similar J200 (DCT2500) like solution.
dagra82
Junior Member
Posts: 108
Joined: Fri Apr 07, 2006 1:27 pm

Post by dagra82 »

Mr usbbdm I sent him a package with the dvi.
I unsolder a flash of a dvi with firmware, boot and nvram well written and tested and the soldier to another with the flash dvi broken, the result was that I wanted to update and dvi nt usbjtag not detected the flash, but solde the I thought that flash was broken and the other dvi me so well detected.
I think it's an internal fault
novatoevc
Junior Member
Posts: 2
Joined: Thu Mar 18, 2010 10:12 am

Post by novatoevc »

draga, pon tu post en español que no se entiende muy bien que estas diciendo. ya te lo traduzco yo al ingles
dagra82
Junior Member
Posts: 108
Joined: Fri Apr 07, 2006 1:27 pm

Post by dagra82 »

yo cogi la flash de un dvi 3120 el cual funcionaba bien y se detectaba todo bien , la desolde y la solde en el otro dvi 3120 el cual tengo que no detecta la flash . Yo pensaba que al soldarle la nueva flash bien programada al dvi3120 volveria funcionar , pero no se queda en modo de actulizacion (lo dejo actualizar y me da error) y ademas me sigue sin detectar las flash, sin embargo solde la flash que pensaba que estaba roto en el otro dvi 3120 y me lo detecto a la primera y la pude programar .
Conclusion el fallo es interno y no por culpa de la flash .
Yo pienso que la operadora esta haciendo algo con los dvi los cuales tiene puesto el antiretorno ya que se rehinician mucho y los dvi 3120 no lo soportan bien ni tampoco el calor y se ropen sin embargo los dvi 3020 duran mas.
novatoevc
Junior Member
Posts: 2
Joined: Thu Mar 18, 2010 10:12 am

Post by novatoevc »

dagra82 wrote:yo cogi la flash de un dvi 3120 el cual funcionaba bien y se detectaba todo bien , la desolde y la solde en el otro dvi 3120 el cual tengo que no detecta la flash . Yo pensaba que al soldarle la nueva flash bien programada al dvi3120 volveria funcionar , pero no se queda en modo de actulizacion (lo dejo actualizar y me da error) y ademas me sigue sin detectar las flash, sin embargo solde la flash que pensaba que estaba roto en el otro dvi 3120 y me lo detecto a la primera y la pude programar .
Conclusion el fallo es interno y no por culpa de la flash .
Yo pienso que la operadora esta haciendo algo con los dvi los cuales tiene puesto el antiretorno ya que se rehinician mucho y los dvi 3120 no lo soportan bien ni tampoco el calor y se ropen sin embargo los dvi 3020 duran mas.
I unsolderd the flash of a perfectly good dvi 3120 who's flash I was able to detect with no problem. I then solderd this flash to another dvi3120 who's flash I was unable to detect. I thought that after soldering this new and well programmed flash to the broken dvi that it would work again. But no to my surprise, when I switched it on it starts to update it self (after the update it gives me an errror) and I still can't detect the flash. My next step was to solder the supposedly broken flash to the working dvi3120 and amazingly it works at first go, and lets me program it.
My conclusion is that thier must be an internal error and not because of a faulty flash.
I think that the internet company is doing something to the dvi's who have their return cut off, I think this is so becuase they often restart themselves, which dose'nt seem to do the dvi3120 any good. They also seem to heat up alot which causes them to breakdown. On the other hand the dvi3020 see to be able to cope with this a lot better.
techouk
Junior Member
Posts: 6
Joined: Wed Mar 08, 2006 10:41 am

Post by techouk »

Hello, you hAVE probably broken some component. This random response to detect is (i think) some diode, capacitor or transistor not working properly. It may be too the altera component ( or any other, sorry).
It should be interesting to know what others modifications have you in the box.
Locked

Who is online

Users browsing this forum: No registered users and 4 guests