WRT54g V8

This is JTAG to debrick any JTAG device. Modem, cable boxes, dish boxes routers.
d0
Junior Member
Posts: 177
Joined: Thu Feb 26, 2009 9:50 am
Location: S FL
Contact:

Post by d0 »

the flash chip is Samsung k8d1716ubc and the broadcom 5354
d0
Junior Member
Posts: 177
Joined: Thu Feb 26, 2009 9:50 am
Location: S FL
Contact:

Success

Post by d0 »

SUCCESSFULL DEBRICK OF WRT54G V8
Thank you for you support
459fta
Junior Member
Posts: 15
Joined: Mon Sep 10, 2007 6:09 pm

Post by 459fta »

usbbdm,
my WRT54gV8 is bricked so bad after trying to load dd-wt fm, all 5 lights from right to left are up.
i'm using usbjtag 0.30v and i'm only getting:
detect
IDCODE 2535417F
Broadcom Part NotFound 5354
IMPCODE 810904
DMA supoorted

In your prev post you said "USB JTAG NT is the solution. The old USB JTAG has issue when detect and since clone exist, no more fixes for the clone"

But, is any way to debrick this sh**t with 0.30 Licensed version?
maybe a good def file will help?
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

There is some luck you can do. 3.3V is one solution for old USB JTAG. It is possible but very hard.
The detect lockup is the problem so you need to do a lot of unplug/power off/on to get out of the state.
Def file will not do any help in debricking the router.
The method used in NT is to stop the CPU at bootup and you have full control. The clone is all it does to stop the development of old USB JTAG. The time spent on debrick V8 with old USB JTAG will be much longer than NT. All I am saying is possible but harder and longer.

USB JTAG NT software was based on USB JTAG.
0.01 of NT equals to 0.31 of USB JTAG.You can see how much the NT has been enhanced.
459fta
Junior Member
Posts: 15
Joined: Mon Sep 10, 2007 6:09 pm

Post by 459fta »

usbbdm, payment is sent, please check your '[email protected]' email
d0
Junior Member
Posts: 177
Joined: Thu Feb 26, 2009 9:50 am
Location: S FL
Contact:

Post by d0 »

Mine was bricked pretty bad too.
459fta
Junior Member
Posts: 15
Joined: Mon Sep 10, 2007 6:09 pm

JTAG NT - Unknown flash type!

Post by 459fta »

usbbdm, i need your help

(DEBUG OFF)
Copyright http://www.usbjtag.com 2008,2009,2010
USB JTAG NT 0.27a
-tap c
Eco :00000000
-tap a ffffffff
Eco :00C12000

(Still DEBUG OFF) powered off/on (Still DEBUG OFF)

-detect
IDCODE 2535417F
Broadcom BCM5345
IMPCODE 00810904
EJTAG V2.6
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
-tap c
Eco :00000000
-tap a ffffffff
Eco :04C92000

(DEBUG ON)

-detect
IDCODE 2535417F
Broadcom BCM5345
IMPCODE 00810904
EJTAG V2.6
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

wait and setup VNC . I can help you program it.
459fta
Junior Member
Posts: 15
Joined: Mon Sep 10, 2007 6:09 pm

Post by 459fta »

finally
after 3-4 time
of using tap c, tap a ffffffff
success ( great tool jtagNT!)
-detect
IDCODE 2535417F
Broadcom BCM5345
IMPCODE 00810904
EJTAG V2.6
DMA supoorted
Found Address= 9fc00000 K8D1716UB

but after power off/on still 5 lights still on
what to do next?
459fta
Junior Member
Posts: 15
Joined: Mon Sep 10, 2007 6:09 pm

Post by 459fta »

I think i need cfe file for v8
where i can get this file?
459fta
Junior Member
Posts: 15
Joined: Mon Sep 10, 2007 6:09 pm

Post by 459fta »

strange problem
first time detect, second no
-detect
IDCODE 2535417F
Broadcom BCM5345
IMPCODE 00810904
EJTAG V2.6
DMA supoorted
Found Address= 9fc00000 K8D1716UB
-detect
IDCODE 2535417F
Broadcom BCM5345
IMPCODE 00810904
EJTAG V2.6
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum 0000,0000
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

You need to put the DEBUG ON state and then erase the cfe. Then sprogram the cfe.
459fta
Junior Member
Posts: 15
Joined: Mon Sep 10, 2007 6:09 pm

Post by 459fta »

usbbdm wrote:You need to put the DEBUG ON state and then erase the cfe. Then sprogram the cfe.
When DEBUG is OFF i can detect
-detect
IDCODE 2535417F
Broadcom BCM5345
IMPCODE 00810904
EJTAG V2.6
DMA supoorted
Found Address= 9fc00000 K8D1716UB
-tap c
Eco :00000000
-tap a ffffffff
Eco :04C12000
When DEBUG is ON - Unknown flash type!
-detect
IDCODE 2535417F
Broadcom BCM5345
IMPCODE 00810904
EJTAG V2.6
DMA supoorted
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum ffff,ffff
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

I would have to take a look to determin what is the problem.
If you can detect without DEBUG ON you should be able to erase the CFE and program the good CFE into it.
Post Reply

Who is online

Users browsing this forum: No registered users and 10 guests